|
|
|
|
|
|
HomeCell PhonesCell Phone AccessoriesBlackBerry AccessoriesReusable Screen Protector for Blackberry Bold 9000 |
|
|  | | | Customer Reviews: | | | Average Customer Review: ( 59 customer reviews )
Write an online review and share your thoughts with other customers.
Most Helpful Customer Reviews
20 of 20 found the following review helpful:
 Fits well but extremely difficult to install well Nov 23, 2008
By B. Humphrey
I bought this to install on my new unopened bold. I installed it the instant I pulled the protective plastic off the screen that it shipped with. I'm not sure I'd pay the money to do it again. You pay $3 to ship this item that arrives with a .42 cent stamp. Unless you place it perfectly the 1st time, it just won't look great. You have to kind of curl it and lay it down gradually or you'll have bubbles and not much fun getting them out. You also have to have it aligned perfectly or the edges will be lifted up by the frame of the phone screen. Again, if you have to pick it back up to reapply, you've lost it. I think if someone had practice with these things, they could get satisfactory results, but I'm not sure someone trying it for the first time will have much luck.
dsI'd skip it.
11 of 11 found the following review helpful:
 Exactly what I hoped to get Jan 27, 2009
By M. Whittingham
This product comes with a plastic on both the front and rear of it and a piece of paper telling you to remove one before installation and the other after installation so the real film is always protected until installation time. When I tried to install it, it went over the edge of the right side of the screen so I had to take it back off, by the time I replaced it there were 2 pieces of lint underneath it so I decided to see if it was really washable and reusable so I washed it with just water, when I was done I air dried it but because of impatience I used the edge of the cloth to just dab the areas and so even more lint got underneath but I was tired so I left it that way.
At a later date I removed it and washed it with shampoo but when it dried I saw lots of fingerprints on the sticky side so I washed again with dish washing liquid and the cloth that comes with it to try to get rid of the prints, went outside and air dried it, there were still a few prints and small water spots but it looked better than before so I put it down carefully, sticky side up and cleaned the screen on my bold and reapplied it, this time I only have one bit of lint under it but it's really small and my screen looks great, the prints and spots don't show so I decided to leave it as is, perhaps another time i'll try to get out that last piece of lint but it's really small and negligible.
By the way, there's a bit of cardboard that ships with it that is to be used like a squeegee, use this to get out any air bubbles that may occur after installation.
9 of 10 found the following review helpful:
 STUPID WASTE OF MONEY!!! Dec 13, 2008
By PSimon
This product sucks. Pure and simple. It created so many bubbles, one of the key pieces of paper you're meant to remove on the film was so glued on, I had to scrape and use alcohol to get it off completely, and then, after all that work, there was simply no getting around the fact that the brilliance of the Bold screen was significantly diminished with the film on it. I threw it all away in frustration after this 15 minute futile exercise. Don't wast your money people...
3 of 3 found the following review helpful:
Pain in the *** Jun 10, 2009
By Gankaku
"gankaku"
OK the most important thing to realize about this product - there are THREE pieces to it.
Sticker 1 side - flexible
The screen protector - hard
Sticker 2 side - flexible
If you remove Sticker 1 side first like I did, don't discard it (like I did). There will be two pieces there - Sticker 1 + the hard screen protector. Discard the filmy part with sticker 2 on it. Then put the hard protector + sticker 1 on the screen. Pull off the filmy sticker 1 part and you'll be good to go.
I've been at this for 45 minutes and it drove me nuts. I was trying to peel off the sticker from the screen - but that filmy part full of bubbles is NOT the part you put on the screen.
They need to include better instructions.
I gave it a 2 for the fact that I have a bit of air on one side where it won't lay flat, and because the instructions were not good. I see other folks here ad the exact problem I had. I'll eventually have to get another one because mine won't lay flat on the side. But at least now I know how to do it.
3 of 3 found the following review helpful:
Surprisingly good, really! Jun 05, 2009
By J. Brown
Having been a user of Palm products for many years, I thought this would be just like the many screen protectors I've bought. I was wrong. It is a harder material than those for the Palm screens, easier to install without bubbles and was reusable. I found that to be true when my Blackberry needed to be repaired. It was easy to remove and went on the new pda without too much hassle.... and it still looks new and remains almost scratch free!
See all 59 customer reviews on Amazon.com
|
| | |
|
|
|
|
|
